top of page

Measuring Doorways for Furniture: A Step-by-Step Guide

Nov 1
11 min read

Homeowner measuring an interior doorway

To find out whether furniture will fit through a doorway, measure the narrowest opening on the whole route, not just the front door. Then compare it with the item’s height, width, depth and, for sofas, its diagonal depth. The item has to clear every tight point between the entrance and the room where it will live. A tape measure, a notepad and about twenty minutes will answer the question before delivery day, when changing your mind is expensive and stressful.

 

Below, we walk through the process the way we would on a job: plan the route, measure each opening, check the stairs and corners, and decide what to do when the numbers are close.



TL;DR

 

  • Measure every opening on the route, from the entry point to the destination room, using a metal tape measure. Write each number down.

  • For sofas and sectionals, the diagonal depth must be smaller than the doorway width, according to CB2 Canada’s measuring guide.

  • Check turns, ceilings, banisters, landings and elevators too. Doorways are only one of the places furniture gets stuck.

  • Measure the door with it attached and with it removed. Taking a door off its hinges can add space.

  • If the margin is under an inch or two, plan for help. Our Inhouse Delivery service is $125 and our Assembly Service is $75.

 

Table of Contents

 

 

What to Measure Before You Start

 

Gather a metal tape measure (a soft sewing tape sags and gives you false numbers), a pen and paper, and the product dimensions from the retailer or seller. If you are buying from an online marketplace, ask the seller for the real measurements of the piece, including depth and height, rather than relying on the listing photos.

 

Write two lists. The first is the furniture: height, width, depth and, for a sofa, the diagonal depth. The second is the route: every opening the piece has to pass through. Keeping them separate lets you compare them line by line instead of holding numbers in your head.

 

Before measuring anything, walk the route. Dufresne’s measuring guide recommends identifying the best route first and noting narrow doorways, tight corners and other obstacles. That order saves time. You may find that the back door, though farther from the living room, is wider than the front entry and a much better choice.

 

How to Measure a Doorway

 

A doorway has more than one useful number. Take each of these:

 

  1. Width. Measure the clear opening between the door jambs, at the narrowest point. Include the door stop strip if it is there. Measure at the top, middle and bottom, because frames are not always square, especially in older Ontario homes.

  2. Height. Measure from the floor (or the top of the threshold) to the underside of the top of the frame.

  3. Diagonal. Measure from the bottom corner on one side to the opposite top corner. This is the longest straight line the opening allows, and it matters when a piece has to be tilted.

  4. Door swing. Check how wide the door opens. Restoration Hardware’s delivery guide tells shoppers to measure the doorway’s interior width and height, check how wide the door opens and look for architectural details that may reduce space.

  5. Clearance with the door removed. Ashley Canada suggests measuring each doorway with the door attached and, if you wish, with it removed, since removing a door from its hinges can add space.

 

The door itself is the most common surprise. A door that opens only to 90 degrees leaves the hinges and the door slab sitting inside the opening. Taking the door off the hinges often gives you the extra inch you need, and it is a five-minute job with a screwdriver and a hammer.

 

Don’t forget thresholds and trim

 

A raised threshold, a door closer or thick casing can reduce the usable height or width. Floor transitions matter for heavy items too, since a bulky piece being dragged or dollied can catch on them. If you are curious how people measure a sloping or uneven threshold before fitting a transition, these sloping floor threshold measurements show the kind of detail worth checking.

 

Measuring the Furniture Itself

 

Measure the piece yourself if you can, even if the retailer lists dimensions. Take the overall height, the widest width (usually the arms on a sofa) and the full depth from the back to the front edge. Then take the numbers that decide most sofa problems.

 

What is diagonal depth?

 

Diagonal depth is the measurement a sofa needs when it is tilted on its end to pass through an opening. CB2 Canada defines it as the distance from the top-left corner to the bottom-right corner of the sofa’s side profile, measured with a metal tape and without pillows. The same guide says that for sofas and sectionals the diagonal depth must be less than the doorway width.

 

That is why a sofa that is 84 inches long and 36 inches deep can slide through a 32-inch door. Turned on its end, the sofa is no longer being asked to pass through as a 36-inch-deep object. It passes as a profile whose diagonal might be 40 inches or more, then gets angled slightly, and the door width has to exceed that diagonal number.

 

A worked example

 

Here is an illustration with made-up numbers, not a specific product:

 

Measurement

Sofa

Opening

Fits?

Height

34 in

80 in door height

Yes

Width (arm to arm)

84 in

32 in door width

Only if turned on its end

Depth

38 in

32 in door width

No, flat on

Diagonal depth

31 in

32 in door width

Yes, by 1 inch

In this example the sofa passes only if the diagonal depth is less than the door width, and a one-inch margin leaves almost no room for error. You would remove the door from its hinges, protect the frame and plan for two people. A comfortable margin is two or three inches. A margin this tight is where our crews are most often asked to help.

 

The quick formula many people use is to make sure two dimensions of the item are smaller than the two dimensions of the opening. It is a sensible first screen, but use diagonal depth for the final decision on a sofa.

 

Measure the Whole Route, Not Just the Door

 

The front door is the opening people measure. The hallway turn, the stair landing and the bedroom door are the ones that stop deliveries. Measure each of the following on your route.

 

Hallways and turns

 

Measure hallway width and height, and look at what sits in the way: radiators, light fixtures, wall sconces, railings and low ceilings. CB2 Canada advises accounting for turns, fixtures, ceilings and banisters. If the hallway makes a right angle, a long piece may need more clearance at the corner than the hallway width suggests. Restoration Hardware also points out entry clearances needed to turn.

 

A useful trick is to cut a cardboard box or tape the footprint of the furniture on the floor. Walk a template of the length and depth through the corner. If a long piece can’t pivot on paper, it won’t pivot in real life.


Cardboard furniture template turning a hallway corner

Stairs and landings

 

Stairs are where measurement mistakes cost the most. Ashley Canada lists the stair measurements to take: the height from the ceiling to the bottom step, the ceiling height at landings and the height from the ceiling to the top step. If the stairway ends at a wall, measure the space from the wall to the top of the stairs. Dufresne’s guide adds each staircase segment including handrails and banisters, plus landing width, depth and ceiling height.

 

Restoration Hardware’s advice for stairs is to measure the width around handrails or posts, the ceiling height from the top and bottom steps, and whether the item can fit around landings. That last point is the one people skip. A narrow stairway might be fine on the straight run but impossible at the half landing where the piece has to turn. If you are checking clearance, ceiling height, landings and fixed fixtures before carrying furniture up or down, this walkthrough of stair and landing measurements offers a useful frame for what to look for.

 

If stairs are involved, read our guide to moving furniture upstairs safely. It covers when carrying is realistic and when a crew is the safer choice. Our article on stair carry fees explains how movers charge for them, so you can ask for them to be itemized up front.

 

Elevators

 

In condo and apartment buildings, the elevator can be the narrowest part of the route. Ashley Canada says elevator checks should include height, width, depth and diagonal measurements, with the elevator diagonal running from the bottom centre of the door to the back centre of the ceiling. Dufresne’s guide covers the elevator door, the interior height, width and depth, and diagonals. Also ask building management about booking the elevator and any padding requirements, since many Ontario buildings require a reservation for move-in.

 

Two of our related guides help if your route includes an elevator or a walk-up: Stairs and Elevators: Get Fees Itemized Before You Book and our 8-week plan to move a walk-up. If you are checking turning clearance, interior walls and obstacles between the entrance and the room, these apartment moving tips are a handy cross-check.


Elevators

A Simple Measuring Checklist

 

Use this order, and you will rarely miss an opening:

 

  1. Note the item’s height, width, depth and diagonal depth.

  2. Choose the route from the outside entry to the final room.

  3. Measure the width, height and diagonal of every doorway on that route.

  4. Measure hallway widths and note any turns.

  5. Measure stair height, landing size, banisters and ceiling height.

  6. Measure the elevator, if there is one.

  7. Compare the smallest opening with the largest dimension that has to pass through it.

  8. Add a margin of at least an inch or two for hands, protective wrap and a bit of play.

  9. Take photos of tight spots and share them with whoever is helping you.

 

Photos are worth the effort. When a customer sends a picture of the stair landing with a measuring tape in the frame, we can plan the carry before arriving.

 

What to Do When the Numbers Are Close

 

A margin of an inch or less is not a green light. It is a reason to take precautions. Try these steps in order:

 

  • Remove the door. Ashley Canada’s advice to measure with the door off applies here. Pop the hinge pins out and set the door aside.

  • Take off the legs. Many sofas and bed frames have legs that unscrew. That can add a little height and make tilting easier.

  • Remove cushions and arms where designed to come off. Some sofas and sectionals are built in modules, and your product manual will tell you what is meant to detach.

  • Switch the route. A back door, patio door or balcony may offer a wider opening.

  • Plan for disassembly. Beds, desks, wardrobes and shelving are usually designed to come apart. Our guide to furniture disassembly for moving explains how to avoid surprise fees when a piece has to be taken apart and put back together.

 

If you have already tried and it still won’t pass, our guide on what to do when your sofa won’t fit through the doorway covers the next steps, and how to move a couch shows the DIY steps and when to hire.

 

Don’t force a piece through an opening. Scraped door frames, torn upholstery and strained backs are the usual result, and a damaged frame on a rental can come out of your deposit.

 

Our Perspective

 

Most delivery problems we see are not caused by big mistakes. They come from one unmeasured spot: a landing, a hallway corner, a bedroom door with a thick frame. By the time a piece is stuck, everyone is stressed and the options are fewer.   That is why we like to see the route measured before the booking. A customer who sends us the opening widths, a photo of the stairs and the item’s diagonal depth gives us what we need to quote clearly. Our pricing is itemized or flat-rate, so you know what you are paying for before the work starts, with no hidden fees.   We are a family-run team, and since 2021 we have completed over 500 moves. The same careful approach applies to a single sofa or a full household: plan the route, protect the home and keep you informed with updates along the way.   If your measurements leave you unsure, you do not have to guess. Send us what you have, and we will help you decide whether the piece can be carried in, needs to be taken apart, or needs a different route.   Natalie

 

When It Makes Sense to Hire Help

 

Measuring tells you whether furniture can fit. It does not tell you whether you should carry it. Heavy sofas, sleeper sectionals, wardrobes, appliances and pianos are awkward even when the opening is wide enough. Narrow stairs, a tight landing or a third-floor walk-up change the answer. The guide to moving a piano is a good example of an item where hiring pros is the safer choice.

 

Help is also worth considering when you are buying from a marketplace. You have measured, the seller is meeting you, and the piece is on the other side of the city. A short in-home delivery avoids borrowing a truck and recruiting friends.

 

Book Help for Delivery, Assembly or a Small Move

 

If you have measured and want the piece moved without the hassle, we can help. Our Inhouse Delivery service is $125 and is built for large or bulky items such as furniture and marketplace purchases. If the item has to come apart and go back together, our Assembly Service is $75. A Small Move for fewer than 10 large items is $225. All of them can be booked on our online booking page, and we serve communities across Ontario including London, Hamilton, the Niagara region and Sarnia.


Atlaskings

If you move often or have several projects planned, the ATLAS PASS is $312 per year. See the landing page for details. Send us your measurements and photos when you book, and we will plan the route with you.

 

FAQ

 

How do I measure a door to see if a couch will fit?

 

Measure the clear width and height of the opening with a metal tape, then compare them with the couch’s height, width, depth and diagonal depth. For a sofa, the diagonal depth has to be smaller than the doorway width, per CB2 Canada’s guidance. Repeat the process for every hallway, stairway and door on the route.

 

What is the diagonal depth of a sofa?

 

It is the diagonal distance from the top-left corner to the bottom-right corner of the sofa’s side, measured without pillows. CB2 Canada uses it to decide whether a sofa can be tilted through a door. Measure it with a rigid metal tape so the number is accurate.

 

What should I do if a sofa won’t fit through the door?

 

First remove the door from its hinges and re-measure, since that can add space. Then try unscrewing the legs, removing any detachable parts or switching to a wider entrance such as a patio door. If it is still too tight, stop and get help rather than forcing it. Our guide to what to do when your sofa won’t fit covers the options.

 

Should I measure with the door open or closed?

 

Measure the opening with the door attached and fully open, then again with it removed. The first tells you what you have today, and the second tells you what you can have with a few minutes of work. Check how wide the door actually opens, since the swing can limit the gap.

 

How much extra space should I leave?

 

Aim for at least an inch or two of margin beyond the tightest measurement, more for heavy items or when protective wrap is used. A margin under an inch is a signal to remove the door, plan for two or more people or have a professional crew handle the carry.

 

Sources

 

Recommended

 

 
 
 

Comments


bottom of page